英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字,中文词皆可:


请选择你想看的字典辞典:
单词字典翻译
slugged查看 slugged 在百度字典中的解释百度英翻中〔查看〕
slugged查看 slugged 在Google字典中的解释Google英翻中〔查看〕
slugged查看 slugged 在Yahoo字典中的解释Yahoo英翻中〔查看〕





安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Slugged my 357 Colt King Cobra - Cast Boolits
    Each cylinder throat should be slugged and compared They should all be within 0 001" or preferably less to one another Throat diameters should be anywhere from 0 0005 to 0 0020" over the bbl's groove diameter Larger calibers seem to be able to handle throats on the large side of this better than smaller ones like the 357
  • Slugged my mosin barrel. . . confused by the readings. - Cast Boolits
    Assuming those are the measurements from land to land and from groove to groove, they are pretty much OK More significant is that the slug should push all the way through the barrel without encountering tight or loose spots - except that some throat erosion in a well-used rifle is normal
  • Just slugged the bore on my Marlin 45 70 Microgroove - Cast Boolits
    Greetings all My first post on what looks to be a treasure trove of information I'm having some accuracy problems with my Marlin 1895 45 70 Microgroove barrel I've just slugged the bore using a plain lead 500 grain bullet It took some tapping through but seemed fine
  • bullet size . 455 Webley - I slugged! - Cast Boolits
    I slugged with fresh-cast 455 bullets out of my hollow-base RCBS 265 grain Webley clone mold that had not yet been sized Alloy is a fairly soft 23-1 range scrap The slug came out of the bore at 450" for the groove diameter We sized the rest of them at 452" and seated them in Hornady 455 cases with 4 grains of Unique
  • New Vaquero slugged too tight? - Cast Boolits
    I ran my 451 slug through my barrel after I sized it through my throats I found at 451 a sized boolit could easily be pushed through all my throats with very little pressure with the use of my finger or a pencil When I slugged my 451 sized boolit through my barrel I had plenty of deep grooves in my boolit (slug) from the barrel lands grooves
  • Ive slugged the bore - Cast Boolits
    In the interest of being more accuracy minded I followed the examples set here and I slugged my first revolver this morning I picked up a beautiful older (maybe 80's) Ruger Blackhawk in 357 Magnum With a nice short barrel this is intended to be a packing around gun for camping and fishing
  • My . 44-40 slugged to . 432. What mould can I use? - Cast Boolits
    It slugged to 432" but all 44-40 moulds I have seen have been 430" at the largest I looked at some at Buffalo Arms and Lee Go to the LBT site and look and the Sale" section of molds and se if you find one in the diameter you need
  • . 001 or . 002 over slugged diameter? - Cast Boolits
    I just started casting for my Gold Cup The bore slugs right at 451” so I ordered a NOE 452 sizer The boolit is a powder coated 200 SWC (50 50 COWW PB) and comes out of the sizer at 453+
  • Slugging a lever action? - Cast Boolits
    I've slugged single-shots, bolt-actions, and revolvers, but never a lever action I assume that I do it the same, but start from the muzzle? I'm concerned about this assumption in relation to damaging the crown Any instruction as to how to go about this? I need to slug a 30-30 Win 94AE Thanks! Selmerfan
  • 350 Legend Bore Diameters - Cast Boolits
    I'm wanting to use the larger diameter and more prolific bullets that are easier to find and sometimes cheaper than 355 It's also easier to find heavy 180+ grain 358 359 360 molds as well If you have any 350L barrel and have slugged the barrel please give your findings below (good or bad)





中文字典-英文字典  2005-2009