英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
reth查看　reth　在百度字典中的解释百度英翻中〔查看〕
reth查看　reth　在Google字典中的解释Google英翻中〔查看〕
reth查看　reth　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • what is mean by Reth interface | SRX - Juniper Networks
    Reth is short for Redundant Ethernet interface These are used on clusters of two SRX devices as part of the failover mechanism With Redundant ethernet a pair of ports back each other up Only one of the two ports is active at a time and one port is on each member of the cluster
  • RETH interfaces with same vlan-id and one GW | SRX
    Third - If is not possible to use reth and irb in same time, for example for reth0 111 and irb 111 does that mean that all configuration for reth0 it should be change to IRB I mean to delete Reth interface and add the ports from reth0 to IRB interfaces and then to add the IRB interfaces to proper security zones
  • SRX Cluster - Using Reth without LACP with Cisco standalone switches
    Not sure, but it looks like you are confusing reth (redundant ethernet) with ae (aggregated ethernet or port channel on Cisco) With reth interfaces these are configured as standard single ethernet ports The pair are redundant so that one and only one is passing traffic at any time depending on the failover status of the reth group on the SRX
  • question about vlan-tagging and reth | SRX
    Hi, if you need vlan-tagging on redundant interfaces, where do you put the vlan-tagging configuration? in the physical interface config (ge-x x x) or the reth i Log in to ask questions, share your expertise, or stay connected to content you value
  • SRX1500 - Reth | SRX - Juniper Networks
    This is all good but then, it says "For failover use the following ports for the reth and tie to redundancy groups" set interfaces xe-6 0 0 gigether-options redundant-parent reth0 set interfaces xe-6 1 0 gigether-options redundant-parent reth1 set interfaces xe-18 0 0 gigether-options redundant-parent reth0
  • SRX240 (HA) issue (RETH interface) | SRX - Juniper Networks
    It is not normal You should be able to ping to the reth interface IP Just check if you have associated the reth interface with a zone correctly and then most importantly you have ping as host-inbound-traffic system-services setting under either that zone level or reth interface level
  • ae interface and reth interface | SRX - Juniper Networks
    Redundant Ethernet Interface(reth) An interface bundle made up of two or more Ethernet links, equally from each node in the cluster to form a single logical interface, acting as Active- Passive pair; Used in a cluster where userspace daemon JSRPD determines the active member; One IP Address, One vMAC owned by node with active member
  • RETH Interface Monitoring on LACP Bundle? | SRX - Juniper Networks
    H'm: did you try to monitor on the reth interface with a weight of 255 ? dark1587 02-20-2012 20:50 In regards to node1, yes I did and the cluster status for node1 still stays at 2
  • RETH interfaces not getting created | SRX - Juniper Networks
    I think you must set units as vlans, try configure like this example in reth interface: vlan-tagging; unit 10 { family bridge { interface-mode trunk; vlan-id 10; } unit 120 { family bridge { interface-mode trunk; vlan-id 120; } Post "run show configuration interfaces reth0"
  • how to see the traffic from reth interface | SRX
    we can see it by the (show security flow session) and if we need to export it we should take a PCAP from both interfaces (reth, and ST) for example, and merge using Wireshark, because from each interface it is capture just one way Thanks for your support-----SUDQI AL-IMAM-----





中文字典-英文字典  2005-2009