英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字,中文词皆可:



安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • LFE vs. LFE+Main - AVS Forum
    Set the subwoofer mode to LFE+Main, you set the Main "crossovers" to 80 Hz (this could vary too), set the other crossovers for the Small speakers to something above those speaker's - 3 dB rolloff points This is what will happen with a 7 1 track (someone correct me if I'm wrong): The LFE track (the 1 in the 7 1) will go to just the subwoofer
  • LFE, subwoofers and interconnects explained | AVS Forum
    The unboosted LFE option on the receiver is often called "LFE -10dB", with the standard boosted option being "LFE 0dB" Alternatively the options might be called "LFE 0dB" and "LFE +10dB" Whatever, the higher option is correct for films and almost all DD and DTS multichannel music
  • What is the LFE input??? - AVS Forum
    LFE effects are recorded in the the 1 channel in multichannel DTS, DD, etc recordings and is recorded at a higher DB level When setting up a sub the reason you see most recommend to bypass the subs crossover is because the receiver will have a crossover settings also and you don't need 2 crossover settings possibly conflicting with each other
  • LFE crossover - 80 or 120 Hz? - AVS Forum
    The lfe channel is independent, and does not pass through the crossover from the main channels to the sub Supposedly the rule for the lfe channel is it may contain content up to 120 Hz So to get all the lfe content calls for a low pass for the lfe of 120 Hz
  • Still confused: LFE, LPF, Crossover - AVS Forum
    LFE is a discrete Low-Frequency Effects track provided on titles mastered with 5 1 Dolby or DTS LFE sends whatever the mix engineer has placed on that channel This, in this circumstance, is bypassing the X-Over on the sub
  • LFE to RCA? - AVS Forum
    LFE is the "low-frequency effects" channel The LFE channel plus all bass (frequencies below the crossover setting in the AVR) from your other speakers channels are output through the "Subwoofer" output (sometimes incorrectly labelled the "LFE" output) on your AVR Subwoofers often have inputs labelled "LFE" in addition to a set of L+R RCA inputs
  • Line In (L+R) vs. LFE - AVS Forum
    Not sure if that's been improved on the new Yamaha models, but you should be good to go using the LFE input My 7 2 4 System, Funk Audio -18"- LFE-Ultras (2) Funk Audio 6 1EP Mains 6 3EP Center, Crowsons Level 2 System, Panasonic DPUB-9000 4K Player, Sony XBR-65"A8H OLED, Marantz SR-8012, Chane A 1 4 Side Rear Surrounds, RSL C34E Atmos (4)
  • Where is the +10dB alignment gain for LFE applied?
    It is sampled using lower resolution and sampling rate than the other channels The decoder extracts it along with all the other channels Bass management combines (sums) the LFE signal with LF signals below the crossover, applying the required LFE signal boost in the process, and sends the resulting signal to the "sub" output of your AVR
  • LFE channel, what actually get sent to sub? - AVS Forum
    The LFE signal is "brickwall" filtered during recording, so there is no content above 120 Hz in the LFE signal Upon playback the user can select an even lower filter point, but this would discard some content in the LFE channel Generally, the LFE LPF should be set at 120 hz to match the LPF of the recording process





中文字典-英文字典  2005-2009